Page 4 of 5
Re: Report bugs in OCP4787 for P3D here
Posted: Sat Oct 27, 2018 8:48 am
by mvr1918
drayton_k:
OK, I can't either explain it.
So, at this time no active bugs are reported and alive.
Re: Report bugs in OCP4787 for P3D here
Posted: Sun Oct 28, 2018 12:07 pm
by martin
Hi Roar,
I followed your advice to reinstall the latest version of QW 787 than uninstalled Sioc and installed Sioc version 6.0 b8 again after that I start a flight first everything is ok but after a few minutes the erratic behaviour starts again but this happens only for the QW 787 for the PMDG no problems.
Martin.
Re: Report bugs in OCP4787 for P3D here
Posted: Sun Oct 28, 2018 8:40 pm
by mvr1918
martin:
after a few minutes the erratic behaviour starts again
I need to get the LOG info from IOCPCONSOLE to look at to investigate this further
When you have this happening again, start IOCPCONSOLE, set LOG ON, move a rotaty to get the erratic data to be logged, then show it here
Re: Report bugs in OCP4787 for P3D here
Posted: Mon Oct 29, 2018 6:22 pm
by martin
Hi Roar,
I made a IOCP log I turn the heading Rotary 1 click to the right that is ok than the next click is not ok it is not 1 degree but 10 degrees the same for the left and the other rotary's.
I also noted that when alt hold is selected the alt starts changing when the alt selector is turned but it must remain the altitute and only changing when lvl change or vs is selected.
Also there is a error called Asynchronous socket error 10053.
Sorry I cannot uplaod the IOCP log because the file is to big I do not now exactly how to upload this file please can you give som information how to do this.
Martin.
Re: Report bugs in OCP4787 for P3D here
Posted: Tue Oct 30, 2018 2:42 pm
by mvr1918
martin:
You can make a zip file and send ut to
roarkrsp@gmail.com
Re: Report bugs in OCP4787 for P3D here
Posted: Tue Oct 30, 2018 7:12 pm
by mvr1918
martin:
I am able to see the issues you have with the rotaries also on my system.
The issue is an QW B787 bug . when in the air QW B787 reacts with randomly 1 or 10 digit increase even though the HW MCP output is the same on ground or in the air.
I will try to get around it in some way if possible. Otherwise I need a fix from QW.
I will report here asap.
Re: Report bugs in OCP4787 for P3D here
Posted: Tue Oct 30, 2018 10:53 pm
by mvr1918
An update to correct Rotary problems for some users vas noe been sent out
Re: Report bugs in OCP4787 for P3D here
Posted: Wed Oct 31, 2018 12:23 am
by martin
Thanks for the update everything works fine now.
Martie.
Re: Report bugs in OCP4787 for P3D here
Posted: Wed Oct 31, 2018 1:12 pm
by mvr1918
Fine, enjoy flying
Re: Report bugs in OCP4787 for P3D here
Posted: Sun Apr 05, 2020 6:21 pm
by drayton_k
Its started again, the dreaded Socket 10061 error for the 787. I have installed the latest OCBAv5 and uninstalled the v4 as you stated to do.
Now I get the error again as I had before, I have tried copying the text into the Qualitywings.in file but still doesnt work.
Its only the 787 I have problems with, every other aircraft is fine. Even the Xplane version works fine.
Can you help Roar?
Thanks