www.flightsim4fun.com - rksoftware

Hello Roar,

Finalized my AVT-OVH, all working fine exept the LE devices panel
When I set flaps only the LED’s on the left part are working. When I push the test button all
LED’s remain off same when I do light test. All annuciators are on exept the LE device.

Testing in Sioc monitor works and all LED’s ok.
I use V4.6 of your script.

Any idea what is wrong?

Thanks

Best regards

Remco

As I do not have the OCH AFT panel myself it is hard for me to check.

Try to find out if things go OK in the IOCP Console. You should be able to see if the correct variables changes as they should.

Also check that the variables use the correct output numbers that you have when viewing in SIOC Monitor.

That is the best advice I can give without looking more into it.

Hi Roar,

Test button is working connected to the wrong input my bad. Below you find a screen dump from IOPC console when pressing test button and set flaps to 2. What i see with my poor knowledge of Sioc is that the leds fot flappos right are not triggered to go on.

2669=1 - LE_FL_Test
208=1 - LE1_transit
210=1 - LE1_full_ext
211=1 - LE2_transit
213=1 - LE2_full_ext
214=1 - LE3_transit
216=1 - LE3_full_ext
217=1 - LE4_transit
219=1 - LE4_full_ext
220=1 - FL1_transit
222=1 - FL2_transit
224=1 - FL3_transit
225=1 - Fl3_ext
226=1 - FL4_transit
227=1 - FL4_ext
228=1 - LE5_transit
229=1 - LE5_ext
230=1 - LE5_full_ext
231=1 - LE6_transit
232=1 - LE6_ext
233=1 - LE6_full_ext
234=1 - LE7_transit
235=1 - LE7_ext
236=1 - LE7_full_ext
237=1 - LE8_transit
238=1 - LE8_ext
239=1 - LE8_full_ext
2669=0 - LE_FL_Test



422=51 - flaps_val
419=3264 - servo_val
419=3 - servo_val
418=51 - FlapPosL
1329=51 - flaps2
432=51 - flaps_v2
429=5712 - servo_v2
429=6 - servo_v2
428=51 - FlapPosR
1328=45 - flaps
422=45 - flaps_val
419=2880 - servo_val
419=3 - servo_val
418=45 - FlapPosL
1329=45 - flaps2
432=45 - flaps_v2
429=5040 - servo_v2
429=5 - servo_v2
427=174 - servo_flaps2
428=45 - FlapPosR
1328=0 - flaps
422=0 - flaps_val
419=0 - servo_val
417=153 - servo_flaps
418=0 - FlapPosL
208=0 - LE1_transit
211=0 - LE2_transit
214=0 - LE3_transit
217=0 - LE4_transit
220=0 - FL1_transit
222=0 - FL2_transit
1329=0 - flaps2
432=0 - flaps_v2
429=0 - servo_v2
427=169 - servo_flaps2
428=0 - FlapPosR
618=0 - DecimalU2
580=0 - DecimalU
208=0 - LE1_transit
209=0 - LE1_ext
210=0 - LE1_full_ext
211=0 - LE2_transit
212=0 - LE2_ext
213=0 - LE2_full_ext
214=0 - LE3_transit
215=0 - LE3_ext
216=0 - LE3_full_ext
217=0 - LE4_transit
218=0 - LE4_ext
219=0 - LE4_full_ext
220=0 - FL1_transit
221=0 - FL1_ext
222=0 - FL2_transit
223=0 - FL2_ext
224=0 - FL3_transit
225=0 - Fl3_ext
226=0 - FL4_transit
227=0 - FL4_ext
228=0 - LE5_transit
229=0 - LE5_ext
230=0 - LE5_full_ext
231=0 - LE6_transit
232=0 - LE6_ext
233=0 - LE6_full_ext
234=0 - LE7_transit
235=0 - LE7_ext
236=0 - LE7_full_ext
237=0 - LE8_transit
238=0 - LE8_ext
239=0 - LE8_full_ext
209=1 - LE1_ext
212=1 - LE2_ext
215=1 - LE3_ext
218=1 - LE4_ext
221=1 - FL1_ext
223=1 - FL2_ext
618=0 - DecimalU2
580=0 - DecimalU
1824=69227 - UtcTime
622=69227 - FsSec
618=1 - DecimalU2
1830=51227 - LocTime
580=1 - DecimalU

Br Remco

I find it strange that there should be any issues with the OVH_AFT script as many users have the OVH_AFT panel and have not reported any issues.

Anyway, try to change the


the line


C0 = &OVH_AFT_POW_ON = 0

to

C0 = &AUDI3_POWER_ON = 0

I have changed the line and All working fine now! Thanks for the support Roar!

Best regards Remco

Good, I mark this topic as SOLVED