Page 1 of 1
Some delay in Altitude MPC control
Posted: Fri May 13, 2022 9:31 pm
by Cmte. Pena
Hi Roar,
I´m starting Oi4FS, I click on the CONFIGURE button, choose 1.Airplane (PMDG B737), choose 2.MFSF/P3D script filter (OCP4NGX v5.5), choose my module (MCPv2), choose the 4.Panels (MCP) and everything works fine, but I´m experiencing some delay when I turn the altitude knob in the MCP and the information in the airplane panel.
I have at the 737_Options the lines:
[Aircraft Config]
FixedConfig=
[Panel State]
StartupPanelState=
[SDK]
EnableDataBroadcast=1
EnableDataBroadcast.0=1
EnableDataBroadcast.1=1
My MCP module is version 2.
What can be wrong?
Re: Some delay in Altitude MPC control
Posted: Fri May 13, 2022 9:37 pm
by mvr1918
It could be a PMDG issue. I have got the same report from another user. I will look into it when I am back in my office next week.
Re: Some delay in Altitude MPC control
Posted: Sat May 14, 2022 5:42 pm
by Cmte. Pena
mvr1918 wrote: ↑Fri May 13, 2022 9:37 pm
It could be a PMDG issue. I have got the same report from another user. I will look into it when I am back in my office next week.
Ok, captain, I´ll waiting.
Re: Some delay in Altitude MPC control
Posted: Wed May 18, 2022 9:36 pm
by mvr1918
Is your MCP ALT display issue only a lag of displaying updated values or does the LVL CHG also turns ON-OFF when you rotate the ALT KNOB on the hardware MCP?
Re: Some delay in Altitude MPC control
Posted: Fri May 20, 2022 2:02 pm
by duri1979
HI
Have the same lag problem, while changing altitude, the LVL change is off...
Re: Some delay in Altitude MPC control
Posted: Fri May 20, 2022 9:46 pm
by mvr1918
After some investigation I found out the the ALT display lag is due to a change in the internal coding in the PMDG 737 for MSFS compared to the PMDG 737 airplane in P3D.
This problem means that it can only be fixed by making new special WASM module of modify the existing Oi4FS Bridge software(WASM) that reads another ALT variable in the PMDG 737 for MSFS.
I have tested this and can verify that the lag is gone with this fix.
I will send out the fix next week as I want to wait a little to see if there are other issues that needs to be fixed as well.
Re: Some delay in Altitude MPC control
Posted: Sat May 21, 2022 4:09 pm
by Cmte. Pena
mvr1918 wrote: ↑Fri May 20, 2022 9:46 pm
After some investigation I found out the the ALT display lag is due to a change in the internal coding in the PMDG 737 for MSFS compared to the PMDG 737 airplane in P3D.
This problem means that it can only be fixed by making new special WASM module of modify the existing Oi4FS Bridge software(WASM) that reads another ALT variable in the PMDG 737 for MSFS.
I have tested this and can verify that the lag is gone with this fix.
I will send out the fix next week as I want to wait a little to see if there are other issues that needs to be fixed as well.
Thank you!!!
Re: Some delay in Altitude MPC control
Posted: Tue Jul 19, 2022 12:20 pm
by mvr1918
Solved and closed