Blank (Flashing) MCPv2 and PMDG737ngx (SOLVED)

[frate]

Hello everyone,
I've been working for several days on my new MCP v2 from Opencockpits, and I can't make it work.
After reinstalling several times OC4BA V3 (following every instruction given in the "MUST READ" file), I was able to switch it on for a couple of seconds.

Power to the module is connected.
USB directly to PC (No HUB).
OC4BA recognizes the module as "MCPv2"
Script used "OCP4NGX_PP_v2.0.ssi" (Tried the other 4 scripts too, with no results)

OC4BA configuration

ScreenConfig.jpg (116.09 KiB) Viewed 5069 times

When it has worked the displays flashed randomly.

What is ALWAYS WORKING:
all the buttons works correctly,also Vs and Heading knob (Hdg Knob changes only bank angle)
But NO light indications.

Here's the log of the moments when everything it has worked.

Code: Select all

151=-1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=-1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=2 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=-1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=-2 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=-1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=5 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=2 - ROTARY_CrsL
151=0 - ROTARY_CrsL
56=1 - AT_ARM_SW
2527=0 - AT_ARM
56=0 - AT_ARM_SW
2527=1 - AT_ARM
56=1 - AT_ARM_SW
2527=0 - AT_ARM
56=0 - AT_ARM_SW
2527=1 - AT_ARM
2531=1 - CO_SW
2531=0 - CO_SW
1260=0 - IASMACH  [b]///APPROX at this time LCDs comes alive, (I don't remeber of any LEDs indications, probably not on)[/b]
2547=0 - MACHtoNGX
26=1 - D_MACHDP
1328=0 - 
1329=0 - 
1101=0 - TransBusOff0
1=2 - EL_STATE
1102=0 - TransBusOff1
1=6 - EL_STATE
20=1 - ATC_Power_ON
274=0 - atc_dsp
269=0 - XPDRFreq
268=0 - XPDRFreqHigh
267=0 - XPDRFreqLow
12=1 - MCP_POWER_ON
145=1 - CDU1_POWER_ON
148=1 - CDU2_POWER_ON
1094=0 - 
2531=1 - CO_SW
11=1 - MCP_R_DELAY
4=1 - Blank
5=0 - Lit
33=0 - BANKHDG
23=0 - D_IAS
2534=0 - D_CrsL
2542=0 - D_Hdg
36=0 - D_ALT
45=0 - D_VS4
44=0 - D_VS3
43=0 - D_VS
2535=0 - D_CrsR
11=0 - MCP_R_DELAY
28=1 - ROTARY_IAS
238=1 - ROTACTIVE_IAS
2547=40 - MACHtoNGX
23=40 - D_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS
2547=41 - MACHtoNGX
23=41 - D_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS
2547=42 - MACHtoNGX
23=42 - D_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS
2547=43 - MACHtoNGX
23=43 - D_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS
2547=44 - MACHtoNGX
23=44 - D_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS
2547=45 - MACHtoNGX
23=45 - D_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS

Thanks in advance

Elia

[frate]

Hi Voss,
Thank you for replying.

Got PMDG 737 ngx boxed version from aerosoft and installed service pack 1
(not sure if it's exactly SP1D, I've installed this update from aerosoft support website
PMDG 737-800/900NGX for FSX / FSX-SE (v1.10.6461)
download at this link http://support.aerosoft.com/index.php?a ... oducts=630 )

Tryed every usb port on my PC (2 front, 4 rear, 2 from an hub).
Databroadcast is enabled (set to 1).

Elia

[frate]

Yes, all buttons and displays are working correctly.
I've tested te MCP with SIOC monitor.
Also using the default 737 from Microsoft, configuring the correct script on SIOC, everything works beautifully.
So displays are ok.

Elia

[frate]

I have SICO 5.0 B5.
Where to download last version?

Elia

[frate]

Procedure followed:
- Reinstalled the PMDG 737 ngx with SP1D
- Powered MCP
- Plugged USB
- Opened FSX, and loaded the 737 on a rwy
- started SIOC (v5.0) and IOCP console
- Log On
- Started OCP4NGX.exe

Log now is empty so I pressed some buttons and moved some knobs.
Here is the Log:

Code: Select all

151=-1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=-1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
151=1 - ROTARY_CrsL
151=0 - ROTARY_CrsL
56=1 - AT_ARM_SW
2527=0 - AT_ARM
56=0 - AT_ARM_SW
2527=1 - AT_ARM
56=1 - AT_ARM_SW
2527=0 - AT_ARM
56=0 - AT_ARM_SW
2527=1 - AT_ARM
2531=1 - CO_SW
2551=1 - SPEED_SW
28=-2 - ROTARY_IAS
238=1 - ROTACTIVE_IAS
2547=40 - MACHtoNGX
28=0 - ROTARY_IAS
28=1 - ROTARY_IAS
28=0 - ROTARY_IAS
28=2 - ROTARY_IAS
28=0 - ROTARY_IAS
28=-1 - ROTARY_IAS
2547=41 - MACHtoNGX
28=0 - ROTARY_IAS
28=-2 - ROTARY_IAS
2547=43 - MACHtoNGX
28=0 - ROTARY_IAS
28=1 - ROTARY_IAS
2547=42 - MACHtoNGX
28=0 - ROTARY_IAS
28=1 - ROTARY_IAS
2547=41 - MACHtoNGX
28=0 - ROTARY_IAS
34=-1 - ROTARY_Hdg
2528=1 - BANKING_SEL
34=0 - ROTARY_Hdg
34=1 - ROTARY_Hdg
2528=0 - BANKING_SEL
34=0 - ROTARY_Hdg
238=0 - ROTACTIVE_IAS
2538=1 - DISENGAGE_BAR
2538=0 - DISENGAGE_BAR
2529=1 - CMD_A_SW
2536=1 - CSW_A_SW

[frate]

OK, I'll send you the mail.

in the mean time i'll be installing the last sioc

Elia

[frate]

Installed SIOC 5.1
DataBroadcast is enabled

nothing changed except this appeared at the beginning of the log first time I've tryied:

Code: Select all

10=1 - SD_DELAY
10=0 - SD_DELAY

Anyway, I've set you Teamviewer info.

Elia

[frate]

To anyone following this thread:
I don't have the SP1D installed correctly.

I'll be posting further news.

Elia

[frate]

I've removed the PMDG 737 ngx and installed the SP1D again.

(What I used to do was:
- Removing the PMDG
- Installing again same version <- This is wrong
- then installing SP1D)

Everything now is working perfectly.

I do apologize beeing that stupid.

Thanks "RK Software" for the excellent and fast support.

Elia

[mvr1918]

This topic is closed and marked as SOLVED